Search results

Create the page "Z80 Assembly" on this wiki! See also the search results found.

• Z80:Directives:FILLW
  Performs the same operation as [[Z80:Directives:FILL|fill]] except that it outputs words rather than bytes. [[Z80:Directives:FILL|fill]]
  324 bytes (40 words) - 08:14, 6 February 2016
• Z80:Directives:FOR
  [[Z80:Directives:REPEAT/REPT|repeat/rept]] [[Z80:Directives:WHILE|while]]
  460 bytes (61 words) - 17:02, 5 February 2016
• Z80:Opcodes:PUSH
  ...hen you want to load a 16-bit register into another 16-bit register (the [[Z80:Opcodes:LD|LD]] instruction won't work for this). [[Z80:Opcodes:POP|POP]]
  891 bytes (132 words) - 01:53, 14 March 2017
• Z80:Directives:EXPORT
  [[Z80:Directives:ENDEXPORT|endexport]] [[Z80:Directives:EXPORTMODE|exportmode]]
  401 bytes (53 words) - 16:38, 5 February 2016
• Z80:Directives:DEFPAGE
  [[Z80:Directives:PAGE/NOPAGE|page/nopage]] [[Z80:Directives:RAWPAGES|rawpages]]
  430 bytes (59 words) - 17:02, 5 February 2016
• Z80:Opcodes:NEG
  [[Z80:Opcodes:CPL|CPL]],[[Z80:Opcodes:SUB|SUB]] [[Category:Z80 Assembly]]
  677 bytes (97 words) - 22:30, 5 February 2016
• Z80:Directives:INCSECTION
  See [[Z80:Directives:SECTION/ENDSECTION|section-endsection]] for more information. [[Z80:Directives:SECTION/ENDSECTION|section-endsection]]
  370 bytes (40 words) - 16:40, 5 February 2016
• Z80:Directives:SCRIPTREFERENCE
  When script files (loaded with [[Z80:Directives:INCSCRIPT|incscript]]) are compiled you need to explicitly refer [[Z80:Directives:INCSCRIPT|incscript]]
  542 bytes (63 words) - 08:15, 6 February 2016
• Z80:Opcodes:CPL
  [[Z80:Opcodes:NEG|NEG]],[[Z80:Opcodes:XOR|XOR]] [[Category:Z80 Assembly]]
  669 bytes (106 words) - 22:38, 5 February 2016
• Z80:Directives:SEGAPRODUCT
  [[Z80:Directives:SEGAREGION|segaregion]] [[Z80:Directives:SEGAVERSION|segaversion]]
  364 bytes (41 words) - 16:40, 5 February 2016
• Z80:Directives:INCBIN
  [[Z80:Directives:INCBMP|incbmp]] [[Z80:Directives:INCTEXT|inctext]]
  412 bytes (51 words) - 17:17, 5 February 2016
• Z80:Ports:Port03
  ...continuously call the interrupt code once interrupts are re-enabled with [[Z80:Opcodes:EI|EI]]. Bit 3: Set 0 to put the calculator in low power mode if and only if the Z80 cpu enters the halt state (during the executing of a halt instruction). Set
  2 KB (375 words) - 23:56, 5 February 2016
• Z80:Directives:DEFINED
  [[Z80:Directives:DEFINE|define]] [[Z80:Directives:IFDEF|ifdef]]
  376 bytes (45 words) - 16:42, 5 February 2016
• Z80:Directives:ELSEIF
  [[Z80:Directives:IF|if]] [[Z80:Directives:ELSE|else]]
  387 bytes (53 words) - 17:27, 5 February 2016
• Z80:Directives:LOOP
  [[Z80:Directives:FOR|for]] [[Z80:Directives:REPEAT/REPT|repeat-rept]]
  305 bytes (36 words) - 16:45, 5 February 2016
• Z80:Directives:SECTION/ENDSECTION
  ...sections isn't compiled immediately. To compile it, you need to use the [[Z80:Directives:INCSECTION|incsection]] directive. [[Z80:Directives:INCSECTION|incsection]]
  937 bytes (101 words) - 17:28, 5 February 2016
• Z80:Directives:DVAR
  ...rmatted to a particular data type. The types used are the same as in the [[Z80:Directives:Var/TVAR/TEMPVAR|var/tvar/tempvar]] directive. [[Z80:Directives:VAR/TVAR/TEMPVAR|var/tvar/tempvar]]
  443 bytes (60 words) - 08:26, 6 February 2016
• Z80:Directives:FAIL
  [[Z80:Directives:ECHO|echo]] [[Z80:Directives:WARN|warn]]
  318 bytes (40 words) - 17:29, 5 February 2016
• Z80:Directives:INCSCRIPT
  ...is a special case. If you specify it, do not pass a value for it from your assembly source file. It will be populated with the instance of the compiler object [[Z80:Directives:SCRIPTREFERENCE|scriptreference]]
  1 KB (178 words) - 08:23, 5 February 2016
• Z80:Directives:FILL
  [[Z80:Directives:BLOCK|block]] [[Category:Z80 Assembly]]
  399 bytes (53 words) - 17:23, 5 February 2016

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)